This type of application has already been written and rewritten. But I will still describe all the methods known to me, seen somewhere, or personally tested.
The technological process of creating a double-sided applique for different options for its location:
Option 1 with hooking the main fabric (when the applique is located in the center of the product or far from the edge)
- The main fabric + stabilizer is placed in the hoop.
- Simple stitching is sewn to show where to put the applique fabric, which will be on the face of the product. Then the machine stops and the hoop moves out to make it easier to place the applique fabric.
- When the hoop is in place, the 2nd appliqué fabric is gently inserted between the hoop and the table.
- This is followed by sewing on the applique fabrics. The machine stops after sewing.
- The hoop is removed and excess appliqué fabrics are cut off on both sides: from the face and from the wrong side. The hoop is inserted back into the machine.
- The finishing border is embroidery digitizing services.
Option 2 without hooking the main fabric (when the applique is located on the corner or edge of the product)
- Only a tear-off dense stabilizer is placed in the hoop.
- Simple stitching is sewn to show where to put the base fabric. Then the machine stops and the hoop moves out to make it easier to put the fabric. The fabric is pre-sprayed with glue to glue it in the right place. Applique fabric is put on it, which will be on the face.
- When the hoop is in place, the 2nd appliqué fabric is gently inserted between the hoop and the table.
- This is followed by sewing on the appliqué fabric to hold it in place. The machine stops after sewing.
- The hoop is removed and excess appliqué fabrics are trimmed on both sides from the face and the wrong side. The hoop is inserted back into the machine.
- The finishing border is embroidered.
Option 3 without hooking the main fabric
- Only a tear-off dense stabilizer or a dense water-soluble one is placed in the hoop.
- Simple stitching is sewn to show where to put the appliqué fabric, which will be on the wrong side. Then the machine stops and the hoop moves out to make it easier to place the applique fabric.
- When the hoop is in place, the appliqué fabric is sewn onto the stabilizer. The machine stops after sewing.
- The excess applique fabric is trimmed off. On this applique, the base and appliqué fabric is put, which will be on the face. They can be fixed to each other with temporary fixing glue.
- The hoop is slid into place and all layers are sewn together. The machine stops after sewing. The hoop should move out.
- Excess application fabric is cut off the face.
- The finishing border is online embroidery digitizing
- This whole sandwich is taken out of the stabilizer.
This method is, of course, easier to implement than the first two, because you don't have to remove the hoop. But the big disadvantage of this method is that none of the fabrics are hooped and a rather unstable structure is obtained, which can be pulled together and deformed during embroidery. This method is only suitable for very small designs.
Digitizing a double-sided applique is based on the same principles as digitizing an overlay applique.
- Creates an outline showing where to put the fabric. Usually, this outline is created with a simple stitch.
- Give a command to stop the machine and leave the frame to position the appliqué fabric. The way the command is set depends on the type of machine.
- Creation of a contour for stitching on appliqué fabric. This sewing contour must be duplicated as many times as there are techniques for cutting appliqués.
- Give a command to prevent the machine and leave the frame to trim excess appliqué fabric. The way the command is set depends on the type of machine.
- Creates a column of finishing stitches.
Recommendations:
- You need to attach the applique fabric around the perimeter with at least simple stitches from the 2nd pass, or better - with a small zigzag.
- The width of finishing satin for applique must be at least 3-4mm.
- The bobbin thread should match the upper thread.
For more details:
https://www.mindstick.com/articles/326927/we-work-with-metallic
Shock! " She giggled. She laughed loudly and replied, '1208. '"That's my room. "The custom sexdolls' girlfriend said, "Do you want to come up?